How to fix Nand Flash Was Not Detected?

NAND Flash was not detected
In today's article, we will disassemble the Nand Flash Was Not Detected error, which is a pretty serious problem for any smartphone owner based on the Android operating system. Meet this error is not so simple: this message pops up in the process of flashing the device during memory testing.

In today's article, we will disassemble the Nand Flash Was Not Detected error, which is a pretty serious problem for any smartphone owner based on the Android operating system. Meet this error is not so simple: this message pops up in the process of flashing the device during memory testing.

Usually, when users understand that their smartphone cannot normally load the operating system, then attempt to flash it, and also perform memory checks (or resort to checking the memory after installing the firmware). They are then faced with the Nand Flash Was Not Detected error.

Translated to the Russian error message translated as "Nand-flash-instant was not detected." The reasons for this error may be the following:

  • physical damage to the NAND memory of the smartphone;
  • unsuccessful attempt to install the firmware;
  • Outdated software to perform flashing;
  • The smartphone is set to protection against software changes.

The NAND-flash memory error solution was not detected

Nand Flash Was Not Detected

Solutions for this problem is not a lot: checking the NAND memory, checking the firmware installed and change the utility to flash. The first to fulfill at home is almost impossible, so we recommend that you go with your smartphone to the nearest service center and rely on local guys. You may have recently dropped your smartphone, as a result of which his memory was damaged.

However, if the memory turned out to be fully order, the problem is likely to be in the installed version of flashing or in the software you are trying to install it. Try to find some other firmware version and install it. Among other things, make sure you follow the instructions attached to the firmware. If it does not help, then use a different program for flashing your smartphone. Any other is suitable - use the search engine and advice from other users. With normally functioning memory, something from this should help you get rid of the Nand Flash Was Not Detected error.

Player recovery: controller definition, flash drive firmware

Nand Flash Was Not Detected What to do?

Hello!

If your flash drive has become constantly climbing: not formatted, when connected to a computer - it often hangs, when copying files to it - errors fly out, but It was not mechanically exposed - there is a chance to restore its performance!

A source: https://ocomp.info/voStanovlenie-rabotyi-fleshki.html.

Nand Flash Was Not Detected What to do

Nand Flash Was Not Detected What to do?44 users consider this page useful.

Some of the mobile devices on the basis of Android OS can stop functioning normally. When you turn on the phone, the user often sees only a single screen flashing, and attempts to clean the device cache (Wipe Cache) do not give the desired result. When trying to flash the system using the appropriate flash utility, the memory test of this program gives the message "Error: Nand Flash Was Not Detected". In this article, I will tell you what the message Error: Nand Flash Was Not Detected, which causes of this error, and how to fix it.

What is ERROR: Nand Flash Was Not Detected

So this is Error: Nand Flash Was Not Detected? First of all, it is worth a response to the question "Nand ​​Flash that is."

As you know (and maybe someone reads about it for the first time), now there are two main methods of the form of flash memory - this is NOR-flash and Nand-flash, differing by the method of connecting cells into an array and read-write algorithms.

If the NOR flash works with small memory, then the NAND flash is used where large amounts of memory are needed (dozens and hundreds of gigabytes). In particular, the memory of the NAND-flash form is widely used in modern mobile devices (smartphones and tablets), allowing you to quickly and effectively solve various digital tasks.

Accordingly, when the user meets with dysfunction of his smartphone and tries to reflash its device (i.e., to install another software shell on it) with the help of specialized programs (usually it is some of the versions of the SP Flash Tool program), then the test of this program can issue Error: Nand Flash Was Not Detected that translated "Error. NAND Flash memory is not detected. "

Causes of Error errors: Nand Flash Was Not Detected

Causes of Error errors: Nand Flash Was Not Detected can be three main types:

  1. Physical failure of the Nand Flash memory of your smartphone (tablet);
  2. Incorrect versions of the firmware files, which is installed on your phone;
  3. Outdated version of the SP Flash Tool program itself.

After we have decided on what it means ERROR: Nand Flash Was Not Detected and what are the causes of this dysfunction, we turn to the methods of its solution.

How to Fix Error: Nand Flash Was Not Detected

So, how to fix Error: Nand Flash Was Not Detected? First of all, it is worth deciding whether your device has been exposed to any physical exposure (for example, if water did not fall into it). If something is, still happened (and recently), then there is a high probability that the flash memory of your device is damaged, and permanently. In this case, the most optimal output will be purchasing a new device.

If nothing with your device did not happen, then try using another firmware version for your device. Pay attention to the scatter file version (Scatter), problems are often observed with it, as well as with inappropriate this Preloader apparatus. The firmware of some devices (for example, Lenovo) must be carried out when the battery is seized from the device.

The specific firmware for exactly your device you will have to search on the network yourself.

Also, when answering the question "How to get rid of Error: Nand Flash Was Not Detected" I advise us to use only the latest version of the SP Flash Tool program itself, as the series of errors that occur during firmware can be caused by the outdated version of the utility mentioned (the precedents were already).

Conclusion

When answering the question "Error: Nand Flash Was Not Detected What does it mean", it should be noted that the most frequent causes of this error are the physical damage to the flash memory of your device, as well as the incorrect versions of the firmware files used to install on the phone. Try searching alternative firmware versions, as well as use the latest version of the SP Flash Tool utility - this will allow you to effectively fighting the error error: Nand Flash Was Not Detected on your device.

Andro-based smartphones>

Error: Nand Flash Was Not Detected when firmware via SP Flash Tool

Causes of Nand Flash Was Not Detected Errors

Nand Flash is a modern way to store information in phones, its memory. Therefore, when an error occurs in memory cells, then the message "Nand ​​Flash Was Not Detected" is issued. You can translate in more detail as "Memory was not found."

Most often, this problem is found for Android devices from Lenovo, and some models with MTK processors.

Memory is damaged for many reasons, but several main maintenance can be distinguished:

  • The most frequent marked the physical breakdowns of the device.
  • It is less common not the correct installation of a new firmware.
  • Outdated programs for flashing.
  • Installed protection against software interventions.

Nand Flash in Samsung devices

Correct Error: Nand Flash Was Not Detected

First of all, the performance of the smartphone itself should be established. That is, you need to make sure that the memory is fully working. Perhaps earlier there were moments of the phone in the rain or fall to the floor. Then cells could simply stop working correctly.

  • The solution in this situation becomes repairs in the service center. We'll have to fully change the Nand Flash to the new one. It is not recommended to try to do it at home, it is very high probability to break other installed modules in the phone.

Refracting

When you were convinced that the memory works properly, you should double-check the installed OS. Perhaps the firmware has defects in its assembly, which leads a smartphone to the emergence of problems. Sometimes, reinstalling updates, users did not carefully read the instructions, so just something is done not in that sequence.

  • Find a completely different firmware version. Make sure the source reliability is that it can be trusted - it is desirable to look for official sites and manufacturer forums. Read carefully applied instructions. After all, sometimes there are options when you should remove the battery before changing updates.

Special utilities

The utility for reinstalling packages of updates can also be broken or outdated. It is because of the obsolete collection that modern phones cease to work as a result. Everything must match your level.

  • Download another version of the program or completely different software with a similar function. There are enough such programs: SP Flash Tool, Rom Manager, FastBoot, also many phone manufacturers have branded utilities for the firmware OS.

It is advisable to try each of the options. You can also try to change your computer and firmware on another operating system.

What is "Error: Nand Flash Was Not Detected"

Flash memory of smartphones and tablets is divided into two parts: for the OS itself and executable files and for storing data (probably you know that the same approach is practiced by the creators of computer operating systems). So, Nand is just a cumulative memory, and the error message says that it is not detected, as if it is not. Of course, all further action becomes impossible, and the firmware is canceled.

Causes of error

There may be several reasons for this:

  • Nand Flash is damaged - for example, the phone fell, lay on something wet, was covered with a plastic case and underwent condensate, etc.;
  • poor-quality firmware (not enough important elements);
  • The version of the utility that the firmware is produced is already irrelevant;
  • Smartphone is protected from attempts to replace software.

How to Fix Error: Nand Flash Was Not Detected

First you need to clarify what exactly the reason for the error "Nand ​​Flash Was Not Detected" to decide what to do. Recall all the "accidents", which happened to your smartphone: Falls, blows, sediment hits, etc. If something it was, then, most likely, you will have to buy a new gadget or go to the service center. Try to purchase / download another firmware, maybe the reason for its incompatibility with the device or the absence of the desired partitions in the Scatter file. Read also requirements for the firmware conditions: from some smartphones before the procedure you need to remove the battery.

Starting with Android 5.1, smartphones are protected by Factory Reset Protection, which eliminates any program changes. It is conceived as a means of protection against thieves, but can create a lot of problems to the user who forgotten the password from the Google account and trying to resolve the issue by flashing.

The bootloader in such devices is blocked, and even the unofficial "pirate" software does not help - it will either pop up the window with a notice that the memory is not found, or the smartphone will persistently require logistics.

If you do not remember your data under which they were recorded in Google, it is better not to try to reflash - at least yourself.

Check also the performance of the utility for the firmware: whether the current version is not outdated, whether it interacts with smartphones of a particular company. If necessary, update it to the last modification. You can also try other programs the same subject - they will probably be more effective. Their mini-rating looks like this:

  • SP Flashtool - take into account that for Windows and Linux there are separate issues;
  • ADB Run - has a rather complicated structure and not Russified: any error can turn the phone into an absolutely non-suitable subject;
  • Bootloader - for the firmware of Sony phones and some others will need additional software - ADB RUN;
  • KDZ UPDATER;
  • FastBoot;
  • Odin;
  • Sony PC Companion - only for Samsung's branded smartphones.

Before you start working with any of them, read the instructions to know in which sequence do all actions and not harm your smartphone. Never interrupt the firmware process that began, otherwise the result can be unpredictable.

A source: https://kztarif.ru/kompjutery/nand-flash-was-not-detected-chto-delat

Errors SP Flash Tool and recommendations for their decision

Nand Flash Was Not Detected What to do?

As you know, in many cases, FlashTool program is used to firmware on MediaTek chips, but, unfortunately, various errors are often found in the process. This instruction contains the most common FlashTool errors and possible solutions to these problems.

(1002 or 0x3ea) s_invalid_arguments

Invalid scatter file. In my case, they were disabled, in Scattere, Preloader and DSP_BL blocks. On it swore.

(1003 or 0x3eb) S_COM_PORT_OPEN_FAIL

Problem with port. It may arise if for example in your BIOS are disabled with COM ports (at least in this case the COM port is virtual here, and the physical USB, but when you disable, you simply won't see the equipment on which the Preloader drivers are set). Either the problem in the USB cable (helps the cable change for the firmware).

Or a problem in the USB port of the computer (the cable is helps to another port).

(1011 or 0x3F3) S_NOT_ENOUCH_STORAGE_SPACE

It occurs when the size of any part of the firmware exceeds the size of the space allotted to it (usually the kernel unit or recovery). It also became known that this error sometimes occurs on the "raw" versions of the flashtula, so it may be possible to change the change of the firmware version.

(1012 or 0x3f4) S_NOT_ENOUGH_MEMORY

Take advantage of the freshest firmware version.

(1013 or 0x3f5) S_COM_PORT_OPEN_FAIL

Error in character and focus is similar to error 1003. It can also help changing the version of the firmware.

You can also try to flash the device with a disabled battery.

(1018 or 0x3fa) S_NKNOWN_TARGET_BBCHIP

Solution: take advantage of the more fresh version of the firmware.

(1022 or 0x3fe) S_UNSUPPORTED_VER_OF_DA

Take advantage of the freshest firmware version.

(1040 or 0x410) s_unsupported_operation

Scatter file does not fit the phone. For example, in the title is 6577, and the phone is actually 6573

(1041 or 0x411) CHS_ERR

Go to the "Help" tab, click "Open Logs Folder" there and delete all logs. Next, go to the folder with the firmware looking for and delete the file "checksum.ini" file. We flash again Format + Dowloand.

(2004 or 0x7d4) S_BROM_DOWNLOAD_DA_FAIL

As it seemed to me, the problem was in the Flashtula version, loaded the version at the end of which there is a SEC designation, in her bodies sewed the first time. Also, the 2004 error may occur if the system is littered with USB-firewood of different other devices. A USBDEVIEW program helped me - deleted all the installed USB drivers and voila, the firmware h / s FT started. Also can help connect the device with a clamping volume key "+" or "-".

It is also offered to try the following: After an error appears, you must immediately close the window with an error and immediately click the download button again.

(2005 or 0x7d5) s_brom_cmd_startcmd_fail

On the phones with MTD flash cases of error occurrence: When you select Download on the Preloader or DSP_BL blocks, you do not have a daw. You need to use the appropriate version of SPFT, for example v2.xxx for MT6573 phones, or turn off the DA Download All. When you select Download on the Preloader or DSP_BL blocks, you have a daw.

You must remove the checkbox from these blocks! If these blocks need to flash, you need to connect the phone in BOOTROM mode. When choosing Readback, Format or MemoryTest. You must connect the phone in BOOTROM mode. You can also try to flash the device with a disabled battery.

He cured the sp_flash_tool_exe_windows_tool_exe_windows_tool_exe_windows_tool.

00_Temp_Secure_Boot, flashed via Firmvare Upgrade, with an inserted battery.

(2020 or 0x7E4) S_BROM_CHKSUM16_MEM_RESULT_DIFF

I decided so - in the settings of the flash station, forcibly put a tank that the body without a battery, after which I connected through the test point with the battery. Everything is surprisingly stitched. It helped the connection of the smartphone with a clipped volume button up (on different phones can be different, such as the volume down or the power button), as soon as the computer and ft identified the phone, let go of the volume and the firmware process went).

(2035 or 0x7f3) S_BROM_CMD_JUMP_DA_FAIL

After clicking the download button, try to connect to the computer the disabled device with the volume with the volume buttons.

(3001 or 0xBB9) S_DA_EXT_RAM_ERROR

It is possible to connect problems. Check the cable and / or reconnect the cable to another port.

(3012 or 0xbc4) nand_flash_not_found

The problem is associated with the definition of the device's flash memory. Famous methods to overcome this problem: try using different versions of the firmware, because As you release different versions, information about flash memory is updated.

Try to flash your smartphone on another computer, because. There are software problems that interfere with correctly define memory on a specific machine.

(3013 or 0xbc5) s_ds_soc_check_fail

It is possible that in the SP_FLASH_TOOL window does not have a bird on Uboot. UBoot is the operating system bootloader + drivers to initialize the main equipment (display, processor, GPIO). Or when there are Russian folder names in the path in the row, for example: C: \ Users \ Kolyan \ Desktop \ Hut \ Firmware \ Firmware Tablet \ 8.31 \ Surfer 8.31 3G_20130402_v1.03 \ surfer 8.31 3g_20130402_v1.03

(3054 or 0xBee) S_DA_N_BOOTLOADER_NOT_EXIST

Helped the change of the version of the firmware with the fifth version on the third

(3066 or 0xBFA) S_DA_HANDSET_FAT_INFO_NOT_FOUND

It occurs with automatic formatting, you should try to set the formatting addresses manually.

(3144 or 0xC48) S_DA_EMMC_FLASH_NOT_FOUND

In addition to the problem with the iron, it may be when Scatter file does not fit the phone. For example, an EMMC is present in the title, and the phone is actually with the MTD Flash. How is the probability that the problem is solved if you use the machine with another operating system (in winxp priority) and find the drivers.

(3149 or 0xc4d) s_da_sdmmc_write_failed

A source: https://jumpmobile.ru/flashtool-errors/

Reviews 'Error: Nand Flash Was Not Detected - how to fix

Error: Nand Flash Was Not Detected - how to fix

Android database smartphones occupy a leading position in the market. However, this does not guarantee their uninterrupted work. Very often, users face different small problems that, fortunately, can be solved rather quickly. You can rightly consider the error "Error: Nand Flash Was Not Detected" by right. It does not allow the mobile device to log in to the OS, and when trying to "reflash" (via SP Flash Tool, for example), reads the message.

ERROR-NAND-FLASH-WAS-NOT-DETECTED-SP-FLASH-SP-FLASH-TOOL

Error: Nand Flash Was Not Detected when firmware via SP Flash Tool

Causes of Nand Flash Was Not Detected Errors

Nand Flash is a modern way to store information in phones, its memory. Therefore, when an error occurs in memory cells, then the message "Nand ​​Flash Was Not Detected" is issued. You can translate in more detail as "Memory was not found."

Most often, this problem is found for Android devices from Lenovo, and some models with MTK processors.

Memory is damaged for many reasons, but several main maintenance can be distinguished:

  • The most frequent marked the physical breakdowns of the device.
  • It is less common not the correct installation of a new firmware.
  • Outdated programs for flashing.
  • Installed protection against software interventions.
Nand-Flash-in-devices-Samsung

Nand Flash in Samsung devices

Correct Error: Nand Flash Was Not Detected

First of all, the performance of the smartphone itself should be established. That is, you need to make sure that the memory is fully working. Perhaps earlier there were moments of the phone in the rain or fall to the floor. Then cells could simply stop working correctly.

  • The solution in this situation becomes repairs in the service center. We'll have to fully change the Nand Flash to the new one. It is not recommended to try to do it at home, it is very high probability to break other installed modules in the phone.

Refracting

When you were convinced that the memory works properly, you should double-check the installed OS. Perhaps the firmware has defects in its assembly, which leads a smartphone to the emergence of problems. Sometimes, reinstalling updates, users did not carefully read the instructions, so just something is done not in that sequence.

  • Find a completely different firmware version. Make sure the source reliability is that it can be trusted - it is desirable to look for official sites and manufacturer forums. Read carefully applied instructions. After all, sometimes there are options when you should remove the battery before changing updates.

Special utilities

The utility for reinstalling packages of updates can also be broken or outdated. It is because of the obsolete collection that modern phones cease to work as a result. Everything must match your level.

  • Download another version of the program or completely different software with a similar function. There are enough such programs: SP Flash Tool, Rom Manager, FastBoot Also, many phone manufacturers have branded utilities for OS firmware.

It is advisable to try each of the options. You can also try to change your computer and firmware on another operating system.

Conclusion

We described the three most frequent options for the appearance of this problem on Android. Of course, they are common and cannot always correct the Nand Flash Was Not Detected error in android devices, as there may be some nuances for each model. But, of course, to start checking from them.

Neirofank1991 @ 09/03/17, 18:23

*

How did the memory died, is it an incorrect file?

Google what is EFUSE.

Neirofank1991 @ 03.09.17, 15:59

*

Do not stick anything but him

It does not sew for the firmware without signature of the manufacturer (Osh.6045) says about it.

There is protection and not native preloader and the interoard will not be allowed.

If there is confidence that this is off firmware, then try ft and yes which for Huaweevian MT6735 \ 6737, for example

Here <-

Patch off the bodies with a downward "down". (Skatter and everything else Estessly choose from your body).

Neirofank1991 @ 09/03/17, 17:37

*

I decided to make a test in the flashlight and did not throw out

But your yes all starts, since Mermori test goes. So forcibly turn the emergency port to "down"

Or as an option - you have 100% you will throw the firmware through the Rightmori (if the test passes, then Rytmemori and Ridbek will also be robbed).

However, it is important to take the "Secret" and "Section", until I killed ...

Добавить комментарий